Laurel BOX Enclosure
Starting at $140.00

Not in stock. Usually ships in 1-2 weeks [?]

Need Help? Call a Calibration Engineer 1-800-884-4967

We're open Mo-Th 8am to 5:30pm. Fr 8am to 5pm ET


  • Sealed on all sides to IP65 / NEMA-4X
  • Includes 1/8 DIN cutout
  • Includes three 0.24" (6.1 mm) cable glands
  • For 1/8 DIN instruments up to 5.30" (134 mm) deep
  • Impact resistant polycarbonate
  • Stainless steel hardware
  • Easy to mount
  • Available with IPC IP67 / NEMA-4X splash-proof cover to protect 1/8 DIN meters from front

This product is an accessory for the following products:

Laurel Laureate AC Voltage & Current Panel Meter
True RMS AC voltage & current meter with 1 cycle update at 50/60 Hz
Laurel Laureate DC Voltage & Current Panel Meter
DC voltage and current indicator with a DC signal conditioner board combine high accuracy, a high read rate and a wide range of output options
Laurel Laureate Load Cell, Strain Gauge & Microvolt Digital Panel Meter
20 mV to 500 mV full-scale ranges, 4- or 6-wire connection
Laurel Laureate Ohm Panel Meter
Optimized for high-speed, high-accuracy resistance measurements in a production environment
Laurel Laureate Process & Ratio Panel Meter
Digital panel meter with scalable readout & control outputs for pressure, level, flow, and other process signals
Laurel Laureate Process Meter & Flow Totalizer
Rate, analog square root, batch control, time based on rate from 0-1 mA, 4-20 mA or 0-10 V signals
Laurel Laureate RTD Panel Meter
Highly accurate and repeatable panel meters factory calibrated for Pt 100, Pt 100 ANSI, Ni 120 and Cu 10 RTDs
Laurel Laureate Scale Panel Meter
Extremely accurate, digital panel meter with 5-digit resolution optimized for weighing applications
Laurel Laureate Thermocouple Panel Meter
Factory calibrated to read type J, K, T, E, N, R and S thermocouples with exceptional accuracy and repeatability
Laurel 88-PRO Panel Meter
Loop powered process meter with a jumper-selectable display range of up to ±199900

The Laurel BOX is a wall-mount / bulkhead enclosure which provides environmental protection to IP65 / NEMA-4X for an 1/8 DIN instrument. It comes with a 1/8 DIN (45 x 92 mm) panel and accommodated instruments up to 134.5 mm (5.30") deep including connectors. This includes all 1/8 DIN instruments by Laurel Electronics and most 1/8 DIN instruments by other manufacturers.

The BOX has an instrument compartment that is sealed on all sides. The two clamshell halves of the case are joined by an O-ring. The rear mounting holes are outside of the sealed compartment. Captive stainless steel screws and high-impact polycarbonate provide durability.

The panel cutout can be expanded by the user up to 150 x 71 mm (5.90" x 2.80") or 131 mm x 110 mm (5.16" x 4.33") to accommodate instruments larger than 1/8 DIN. Internal molded standoffs with a height of 6.5 mm (0.25") can be snipped off by the user if required.

Cable feedthroughs are via three sealed cable glands at the bottom of the case. These make a tight seal with round cables from 6.1 to 1.00 mm (0.04" to 0.24") in diameter. Note that these feedthroughs are not compatible with off the shelf cables with molded connectors, such as USB cables.

The Laurel BOX may be ordered with the IPC splashproof cover. The combination of Models BOX and IPC will provide IP65 / NEMA-4X protection to 1/8 DIN instruments regardless of manufacturer, provided that the instrument depth is less than 134.5 mm (5.30").