ProLink III (Version 3.5, 12/2016) Installation Notes:

This ReadMe.txt file contains the following sections:

NOTE ABOUT CHANGES IN THIS VERSION OF PROLINK III
LICENSE REQUIREMENTS
GENERAL SYSTEM REQUIREMENTS
CONVERTER BOX REQUIREMENTS
TO INSTALL OR UPGRADE PROLINK III
TO UNINSTALL PROLINK III
COEXISTENCE WITH PROLINK II


NOTE ABOUT CHANGES IN THIS VERSION OF PROLINK III

Please see the ChangeLog.txt document in your ProLink III
program folder for information on what changes have
been made in this release of ProLink III.


LICENSE REQUIREMENTS

ProLink III Professional software requires a license key. Detailed
instructions can be found in the ProLink III Quick Start Guide. For
convenience, if you have a serial number, licenses can now be obtained
from the Micro Motion website at:

http://www3.emersonprocess.com/micromotion/ProLinkIII/License.html

ProLink III Basic no longer requires a license key.

GENERAL SYSTEM REQUIREMENTS

To install and run ProLink III, your personal computer must meet or
exceed the following requirements:
- 1 GHz Pentium 4 processor, 2 GHz or higher recommended
- One of the following [for a 32-bit (x86) or 64-bit (x64) processor]:
  - Windows 10
  - Windows 8 or 8.1
  - Windows 7 and 1 GB RAM
  - Windows Vista with Service Pack 1 and 1 GB RAM
  - Windows XP with Service Pack 3 and 1 GB RAM
- Available hard disk space:
  - 1 GB for 32-bit (x86) processor
  - 2 GB for 64-bit (x64) processor
- Video with support for 24-bit color graphics
- 1024 x 768 display minimum, 1280 x 800 or higher widescreen
  format preferred

CONVERTER BOX REQUIREMENTS

ProLink III communication works well with the following converter boxes:
- Microflex RS-485 to RS-232 Converter, Model 101-0009. 
- Microflex RS-485 to USB Converter, Model 101-0020. 
- Microflex MicroLink HART Protocol Modem, RS-232 Interface, Model
  101-0005, converts RS-232 (DB9 F) to Bell 202.
- Microflex MicroLink HART Protocol Modem, USB Interface, Model
  101-0027, converts USB to Bell 202.
All of the above converters provide automatic RTS line control. The USB
converters also require a Windows driver to be installed. The driver is
provided with the converter box and must be installed separately.


TO INSTALL OR UPGRADE PROLINK III

To run ProLink III setup on Windows XP, double-click the Setup.exe file
in the root folder of your CD-ROM drive. To run setup on Windows Vista,
Windows 7, Windows 8.x or Windows 10, you should use 'Run as administrator'.
Once setup starts, follow the directions presented on-screen.

If a previous version of ProLink III software is detected during setup,
the Setup program should be able to upgrade it. If the previous version
was licensed, the new version should be installed into the same folder
in order to reuse the existing license.

After installation completes, the ProLink III program can be found in the
MMI program group available through the Start button on the Windows task
bar. A ProLink III program shortcut is also placed on the desktop for
convenience.


TO UNINSTALL PROLINK III

Use the Windows Control Panel Add/Remove Programs or 'Uninstall a
program' applet to uninstall ProLink III software. In some cases, it
may be necessary to uninstall the ProLink III HART driver separately.

After uninstallation is complete, ProLink III license and database files
will remain behind for reuse by a subsequent installation. Note a later
installation of ProLink III must be to the same folder for the license
files to be reused. If there is no further need of the ProLink III
license or database, the entire folder can be removed.


COEXISTENCE WITH PROLINK II

ProLink III can be installed on the same computer and used side by side
with ProLink II software. If there is a conflict in serial port usage,
close the port in one program to use it in the other.
